MUHAMAD YAMIN BIN BAHARUDIN

• Ensure that valid PTW including JHA are in place for all work performed at site and proper procedures are available and being followed by the contractor to ensure that construction works takes place in an acceptable and organized manner.
• Full time supervision & monitoring on the CONTRACTORs activities at work site to ensure they are carried out in accordance with the approved drawings, specifications, procedures, codes and standards and to the requirements of Regulatory Authorities.
• To ensure contractors meets the plan & target schedule as per project planning and schedule by the PMT ( Project Management Team ).
• To ensure the job activities at site complying with the AFC drawing, ITB, TEQ, vendor drawing and PTS.
• To liaise with electrical engineer regarding the latest drawings and document required.
• To liaise with other discipline to solve on the problem during construction to ensure the smoothness of work done.
• To liaise with contractor representative or 3rd party or authorized inspectors on matters relating to inspection upon electrical items.
• Involved in FAT and SAT for Electrical equipment as such Switchboard, Motor Control Circuit, Cable, Motor, Protection Relay and ENMCS.
• Involved in SD 2022 and TA 2024.
• Involved in Project as such CNU Project, CHIP Project, VIMO Project, COMO Project, ROME Project, Multiverse Project , AVR Project, AIR Project and HOVER Project.
• To ensure the contractors give good commitment in safety, quality and efficiency.

• Ensured safety compliance by maintaining accurate records of instrument inspections, repairs, and calibrations.
• Maintenance work at Eastman Chemical Plant.
• Inspect & repair various type of Electrical & Instrument wiring systems.
• Corrective and preventive maintenance work.
• Perform instrument equipment installation such as control Valve, transmitter, pressure gauge.
• Glanding & termination cable for new equipment such as control valve, transmitter, junction box, electrical motor & etc.
• Perform Electrical & Instrument testing activities – continuity test, loop check, insulation test & etc.
• Good knowledge to read Electrical, Instrument & piping Engineering Drawings such as Electrical schematic drawing, Loop diagram, Hook up drawing, P&ID drawing& etc.

• Monitoring & supervise all job activities.
• Inspect & repair various type of Electrical domestic & industrial wiring systems.
• Involved in maintain generator, machine 3 phase, control circuit, water pump.

• Monitoring & supervise all job activities.
• Inspect & repair various type of Electrical domestic & industrial wiring systems
• Good knowledge to read Electrical, Instrument & piping Engineering Drawings such as Electrical schematic drawing, Loop diagram, Hook up drawing, P&ID drawing& etc.
• Lay electrical & instrument cable for underground & overhead.
• Glanding & termination cable for new equipment such as control valve, transmitter, junction box, switchgear, electrical motor & etc.
• Perform electrical equipment installation such as Electrical Distribution Board, Panel, Switchgear , Motor & etc.
• Perform instrument equipment installation such as control Valve, transmitter, pressure gauge & etc.
• Perform Electrical & Instrument testing activities – continuity test, loop check, insulation test & etc.
• Involved in project such as - CDU 2 Project, NHT2 Project, SPARE HEAT Project (DIALOG), - PERMASENSE MONITORING SENSOR Project (EMERSON), TANK GAUGE SYSTEM Project (ENDRESS HAUSER), - INSTALLATION 6.6KV TRANSFORMER Project (ABB), MPP Project And LAB Project (DOMINANT), NEW DESALTER Project AND TUD Project (DIALOG), FIRE & GAS INSTALLATION Project (DWISOLAR).

• Monitoring & supervise all job activities.
• Inspect & repair various type of Electrical domestic & industrial wiring systems
• Good knowledge to read Electrical & Instrument Drawings such as Electrical schematic drawing, Loop diagram, hook up drawing, P&ID drawing& etc.
• Lay electrical & instrument cable.
• Glanding & termination cable for new equipment such as control valve, transmitter, junction box & etc.
• Perform electrical equipment installation such as Electrical Distribution Board, Panel & etc.
• Perform instrument equipment installation such as control Valve, transmitter, pressure gauge & etc.
• Perform Electrical & Instrument testing activities – continuity test, loop check, insulation test & etc.
• Involve in testing and commissioning.
• Involved in project such as TERMOCOUPLE REPLACEMENT Project (STS), ULSD NEW CUSTODY METERING SYSTEMS Project (TRANSWATER), QRH UPGRADING PROJECT (HZN), REPLACEMENT OF OLD FLOWMETER TOTALIZER Project.

A & SS PROJECT (ABB)

• Replace new A & SS panel in Substation.
• Rewiring on new A & SS Panel.
• Trouble shooting electrical wiring system.

NEW LAB PROJECT

• Involve in construction for New Lab Expansion Project
• Supervise, monitoring and reporting including assist for inspection and testing of the electrical & instrument scope of work.

• Involved in maintain generator, machine 3 phase, control circuit, pump, heating equipment
• Joint encapsulations flanges and valve
• Trouble shooting electrical wiring system

• Troubleshoot and termination work for Flare Project

• Laying electrical cable, glanding and termination work for electrical static at Flare Boom

• Working in shutdown activity.
• Involve in GT 14 c-inspection and responsible to assist Alstom Electrical Engineer for servicing, inspection and testing of ABB MNS Switchgear, motor transformer maintenance and fire fighting system.
• Assisted Alstom during GT commissioning and start-up activity.
• Corrective and preventive maintenance work.

• Laying electrical cable, glanding, termination work for air compressor and installation new main switchboard.

• Involve in shutdown activity for fire & gas project

• joint encapsulations flanges and valve, project at TNB Pasir Gudang

• Improved electrical system safety by conducting thorough inspections and identifying potential hazards.

• working in shutdown activity, corrective and preventive maintenance work.

• working in shutdown activity, wiring junction box for controller safety shower system, testing and commissioning.

• Involve in construction and commissioning activity at PPM(S)B, MTBE & etc.
• Corrective and preventive maintenance work at Substation TUDM Bukit Ibam.

• Servicing electrical equipment for air-conditioner and fire fighting.
• Carry out the testing & fault finding on wiring system.
• Perform troubleshooting on wiring system.

• Servicing electrical equipment for air-conditioner and fire fighting.
• Carry out the testing & fault finding on wiring system.
• Perform troubleshooting on wiring system

• Involve in construction and commissioning activity at PPM(S)B, MTBE & etc.

• Inspect and repair various type of domestic & industrial wiring system.
• Troubleshooting in electrical wiring system.