Elanggo Jayaraman

Product Engineer

. Major in AXI Model V810 S2ex /TRI Xray /Dage 2DX/AOI V500

Diagnose and repair to component level on electronic circuit board assemblies while maintaining minimal quantities of Engineering and Component hold assemblies.
· Exhibit proficiency in the use of electronic test and measurement equipment.
· Ability to understand and utilize assembly documentation such as but not limited to the following; Schematics, BOM’s, Visuals, Debug, Testing tools and procedures.
· Perform as a team member to achieve Diagnostic department’s process yield goals focusing on non product failures (NPFs).
· Assist Test Engineering department in an ongoing data evaluation program for improving the efficiency of the diagnosis of assemblies.
· Support and helping TE install and develop new NPI project.
· Perform PM periodically to prevent all fault failure.
· Understand, recognize and execute Jabil production requirements, rules, policies and procedures ensuring compliance of WIP and 3-5-10 rules.
· Work efficiently to decrease non-preventative maintenance issues to achieve department’s down-time goals.
· Frequent customer interface, including travel to customer sites for advanced diagnostic issues.
· Prepare daily reports and recommend solutions to technical problems as required.
· Perform preventative maintenance program to reduce down time and increase process yields to achieve departmental goals.
· May perform other duties and responsibilities as assigned.
· Enable to conduct test process in conjunction with the customer: In

Circuit Test, Software download, Functional Test, extended tests - Burn In, HASS, Soak Testing, ESS, X-Ray.
· To lead and guide a group of test technicians for supporting production lines.
· To ensure all test equipment are maintained to the best condition for minimum downtime
· To interface with vendors and supplies for machine maintenance and calibration.
·To manage a good level of machine spares parts to ensure minimum production impact due to machine downtime.
· To set up the test equipment for new projects or new businesses.
· To provide cost reduction through automation and process simplification.
· To inspect all incoming test fixtures and jigs to ensure good working condition before release to production line.
· Participates in meetings, seminars and training sessions to stay appraised on new developments.
· Provide Project Management with accurate and timely quotations for all relevant tests, diagnostic and repair functions.
· Review all test processes and identify any untested components.
· Shall supply comprehensive and accurate documentation for all testers, component programmers and debug / repair processes.
· Contribute to the improvement of test yields, test efficiency, tester intermittence, electrical defects and overall tester development.
·Shall contribute to the training of Test Technicians, Debug Technician, Debug Operator, Test Operators and Component programmers.
·Investigate new and existing test and diagnosis methods to improve existing products and support advancing technologies.
· Ensure controls are in place to conform to ISO standards.
· Train and lead the Debug Technicians / Debug Operator to analysis the fault of the production line.
· To trouble shoot and analysis the unit unable repair by Debug Technician.
·May perform other duties and responsibilities as assigned.

Ability

Ability to effectively present information and respond to questions from groups of managers, clients, customers, and the general public.
· Ability to define problems, collect data, establish facts, and draw valid conclusions.
· Ability to operate a personal computer including using a Windows based operating system and related software.
· Advanced PC skills, including training and knowledge of Jabil’s software packages.
· Ability to write simple correspondence. Read and understand visual aid.
· Ability to apply common sense understanding to carry out s

imple one- or two-step instructions.
· Ability to deal with standardized situations with only occasional or no variables.
· Ability to read and comprehend simple instructions, short correspondence, and memos.
· Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals.
· Ability to compute rate, ratio, and percent and to draw and interpret graphs.

People Tree manager

• Managed team of 6 employees, overseeing hiring, training, and professional growth of employees.

EQUIPMENT TEST TECHNICIAN

-Monitor & record mold cavitations on all machines daily

-Provide technical support to shift for trouble shooting and problem resolution.

-Ensure equipment and processes meet and sustain standard production outputs

-Monitor & record mold performance in order to recommend the best mold and machine combination.

-Work closely with tool room & department manager for scheduling any tool work that is required.

-Cover vacations and personal time for Production Supervisors and other Process Techs

-Test and evaluate resins for optimum application

-Maintain and improve upon existing manufacturing practices for the manufacture of finished goods.

-Monitor & record mold cavitations on all machines daily

-Provide technical support to shift for trouble shooting and problem resolution.

-Ensure equipment and processes meet and sustain standard production outputs

-Monitor & record mold performance in order to recommend the best mold and machine combination.

-Work closely with tool room & department manager for scheduling any tool work that is required.

-Cover vacations and personal time for Production Supervisors and other Process Techs

-Test and evaluate resins for optimum application

-Maintain and improve upon existing manufacturing practices for the manufacture of finished goods.